$20.00 Minimum Merchandise Order - Thank You!

Online Catalog:Philmore and Calrad Electronics :Plugs, Jacks, Adapters and Cables:Coaxial Power Plugs/Jacks and Cables:Coaxial Power Plugs With Cord

	0.7 mm ID x 2.35 mm OD with 6' Stripped End 24 AWG Cord Philmore 48-410 Plug is molded to a six foot cable. The other end is stripped and tinned. Mates with: Jack: # 335 PC Jack: # 205 Specifications: Wire Gauge: 24 AWG Complies with EIAJ (Electronic Industries Association of Japan) class 1 or I RC-5320 Standards.   Click Here for Catalog Picture Price:  $2.29
1.3 mm ID x 3.5 mm OD Right Angle 6' Stripped End 24 AWG Cord Philmore TC204 Right angle plug is molded to a six foot cable. The other end is stripped and tinned. Mates with Inline jack: # 256 Chassis jack: # 313 PC board jack: # 211 Specifications: Shielded 24 gauge cable (not zip cord as shown) Barrel Length: 11.50 mm   Click Here for Catalog Picture Price:  $1.96
	1.7 mm ID x 4.0 mm OD Right Angle 6' Stripped End 24 AWG Cord Philmore TC240 Right angle plug is molded to a six foot cable. The other end is stripped and tinned. Mates with: Inline jack: # 262 Chassis jack: # 340 PC board jack: # 207 Specifications: Tip Color is Yellow Wire Gauge: 24 AWG Complies with EIAJ (Electronic Industries Association of Japan) class 2 or II RC-5320 Standards. Barrel Length: 10.4 mm RoHS Compliant   Click Here for Catalog Picture Price:  $1.96
1.7 mm ID x 4.75 mm OD Right Angle 6' Stripped End 24 AWG Cord Philmore TC275 Right angle plug is molded to a six foot cable. The other end is stripped and tinned. Mates with: Inline jack: # 263 Inline chassis jack: # 375 PC board jack: # 220 Specifications: Wire Gauge: 24 AWG Barrel length: 9.6mm Complies with EIAJ (Electronic Industries Association of Japan) class 3 or III RC-5320 Standards. Barrel Length: 9.50 mm   Click Here for Close Up Picture Price:  $1.72
	1.7 mm ID x 4.75 mm OD 6' Stripped End 20 AWG Cord Calrad 55-837 Straight plug is molded to a six foot 20 AWG cable. The other end is stripped and tinned. Mates with: Inline jack: # 263 Inline chassis jack: # 375 PC board jack: # 220 Specifications: Wire Gauge: 20 AWG Complies with EIAJ (Electronic Industries Association of Japan) class 3 or III RC-5320 Standards. Barrel Length: 9.32 mm   Click Here for Catalog Picture Price:  $2.76
1.7 mm ID x 4.75 mm OD 6' Stripped End 18 AWG Cord Calrad 55-837-18 Limited to stock on hand. Straight plug is molded to a six foot 18 AWG cable. The other end is stripped and tinned. Mates with: Inline jack: # 263 Inline chassis jack: # 375 PC board jack: # 220 Specifications: Wire Gauge: 18 AWG Complies with EIAJ (Electronic Industries Association of Japan) class 3 or III RC-5320 Standards. Barrel Length: 9.32 mm   Click Here for Catalog Picture Price:  $3.49
	2.1 mm ID x 5.5 mm OD To Solderless Terminal Philmore 48-1259 This plug is a time saving and inexpensive way for installers to terminate cables with DC power jacks. Only a small Phillips screw driver is required. There is a molded plug on one end, and a solderless terminal at the other end of a 2" flexible cord. The polarity is indicated by a + on the terminal, which is connected to the tip (center) of the DC plug. The solderless terminal has a polarity marking and will accomodate up to 14 AWG wires. Both ends have a flexible strain relief. Mates with: Inline jack # 257 Inline jack with cord: # 48-255, 48-257 Chassis jack # 209, 247, 321 Chassis locking jack: 2112, 2475 (doesn't lock to these) PC board jack # 212 Specifications: Barrel Length: 9 mm Wire Gauge: 20 AWG   Price:  $1.86
2.1 mm ID x 5.5 mm OD Right Angle 6' Stripped End 24 AWG Cord Philmore TC210 Right angle plug is molded to a six foot cable. The other end is stripped and tinned. Mates with: Inline jack: # 257 Inline jack with cord: # 48-255, 48-257 Chassis jack: # 209, 247, 321 Chassis locking jack: 2112, 2475 (doesn't lock to these) PC board jack: # 212 Specifications: Wire Gauge: 24 AWG Barrel Length: 11.50 mm RoHS Compliant   Click Here for Catalog Picture Price:  $1.96
	2.1 mm ID x 5.5 mm OD Right Angle 6' Stripped End 20 AWG Cord Calrad 55-838B-RT Right angle plug is molded to a six foot cable. The other end is stripped and tinned. Mates with: Inline jack: # 257 Inline jack with cord: # 48-255, 48-257 Chassis jack: # 209, 247, 321 Chassis locking jack: 2112, 2475 (doesn't lock to these) PC board jack: # 212 Specifications: Wire Gauge: 20 AWG Barrel Length: 10.0 mm   Price:  $2.79
2.1 mm ID x 5.5 mm OD Right Angle 6' Stripped End 18 AWG Cord Philmore 48-218 Right angle plug is molded to a six foot cable. The other end is stripped and tinned. Mates to: Inline jack: # 257 Inline jack with cord: # 48-255, 48-257 Chassis jack: # 209,247 Chassis locking jack: 2112, 2475 (doesn't lock to these) PC board jack: # 212 Specifications: Wire Gauge: 18 AWG Barrel Length: 12.2 mm   Click Here for Catalog Picture Price:  $2.56
	2.1 mm ID x 5 mm OD 1' Blunt Cut 20 AWG Cord CA-205-1FT-20AWG-BC Plug is molded to a one foot cable. The other end is blunt cut. Mates with: Inline jack: # 257 Inline jack with cord: # 48-255, 48-257 Chassis jack: # 209,247,321 Chassis locking jack: 2112, 2475 (doesn't lock to these) PC board jack: # 212 Specifications: Wire Gauge: 20 AWG Barrel Length: 11mm   Click Here for Catalog Picture Price:  $2.29
2.1 mm ID x 5.5 mm OD 3' Stripped End 20 AWG Cord Calrad 55-838B-3 Plug is molded to a three foot cable. The other end is stripped and tinned. Mates with: Inline jack: # 257 Inline jack with cord: # 48-255, 48-257 Chassis jack: # 209,247,321 Chassis locking jack: 2112, 2475 (doesn't lock to these) PC board jack: # 212 Specifications: Wire Gauge: 20 AWG Barrel Length: 9.5 mm   Click Here for Catalog Picture Price:  $2.54
	2.1 mm ID x 5.5 mm OD 6' Stripped End 20 AWG Cord Calrad 55-838B Plug is molded to a six foot cable. The other end is stripped and tinned. Mates with: Inline jack: # 257 Inline jack with cord: # 48-255, 48-257 Chassis jack: # 209,247,321 Chassis locking jack: 2112, 2475 (doesn't lock to these) PC board jack: # 212 Specifications: Wire Gauge: 20 AWG Barrel Length: 9.5 mm   Click Here for Catalog Picture Price:  $2.66
2.1 mm ID x 5.5 mm OD 8' 22 AWG Cord Stripped/Tinned End CA205-8FT-22AWGSRS/T Plug is molded to an eight foot cable. The other end is stripped and tinned with strain relieve, or it can be cut off if not needed. The barrel length is 11mm Mates with: Inline jack: # 257 Inline jack with cord: # 48-255, 48-257 Chassis jack: # 209,247,321 Chassis locking jack: 2112, 2475 (doesn't lock to these) PC board jack: # 212 Specifications: Wire Gauge: 20 AWG Barrel Length: 9.5 mm   Price:  $2.37
	2.1 mm ID x 5.5 mm OD Spade Lugs & 9ft Cord Revere RTD-ADP2.1 This is a 9 foot white 20 AWG zip cord cable with a 2.1 x 5.5 mm plug on one end, and two 6-32 spade lugs on the other end. Polarity of connector is identified by a red stripe on one of the wires, which indicates the inside center of the plug.   Price:  $3.96
2.1 mm ID x 5.5 mm OD 6' Stripped End 18 AWG Cord Philmore TC218 Plug is molded to a six foot cable. The other end is stripped and tinned. Mates to: Inline jack: # 257 Inline jack with cord: # 48-255, 48-257 Chassis jack: # 209,247,321 Chassis locking jack: 2112, 2475 (doesn't lock to these) PC board jack: # 212 Specifications: Wire Gauge: 18 AWG Barrel Length: 12.5 mm RoHS Comliant   Click Here for Catalog Picture Price:  $2.67
	2.5 mm ID x 5.5 mm OD To Solderless Terminal Philmore 48-1262 This plug is a time saving and inexpensive way for installers to terminate cables with DC power jacks. Only a small Phillips screw driver is required. There is a molded plug on one end, and a solderless terminal at the other end of a 2" flexible cord. The polarity is indicated by a + on the terminal, which is connected to the tip (center) of the DC plug. The solderless terminal has a polarity marking and will accomodate up to 14 AWG wires. Both ends have a flexible strain relief. Mates with: Inline jack # 258 Inline jack with cord # 48-258 Chassis jack # 248, 249, 325 Chassis locking jack: 2512, 2485 (doesn't lock to these) PC board jack # 215 Specifications Specifications: Barrel Length:9 mm   Price:  $1.86
2.5 mm ID x 5.5 mm OD 6' Stripped End 18 AWG Cord Philmore TC258 Straight plug is molded to a six foot cable. The other end is stripped and tinned. Mates to: Inline jack: 258 Inline jack with cord: 48-258, 48-288 and CA206INL10FT18AWG-ST Chassis jack: 248,249,325 Chassis locking jack: 2512, 2485 (doesn't lock to these) PC board jack: 215 Specifications: Wire Gauge: 18 AWG Barrel Length: 12.2 mm   Click Here for Catalog Picture Price:  $2.67
	2.5 mm ID x 5.5 mm OD 6' Stripped End 20 AWG Cord Calrad 55-839B Straight plug is molded to a six foot cable. The other end is stripped and tinned. Mates to: Inline jack: 258 Inline jack with cord: 48-258, 48-288 and CA206INL10FT18AWG-ST Chassis jack: 248,249,325 Chassis locking jack: 2512, 2485 (doesn't lock to these) PC board jack: 215 Specifications: Wire Gauge: 20 AWG Barrel Length: 10.0 mm   Click Here for Catalog Picture Price:  $2.66
2.5 mm ID x 5.5 mm OD 8' Stripped End 20 AWG Cord CA2069.5MM8FT20AWGST Straight plug is molded to an eight foot cable. The other end is stripped and tinned. Mates to: Inline jack: 258 Inline jack with cord: 48-258, 48-288 and CA206INL10FT18AWG-ST Chassis jack: 248,249,325 Chassis locking jack: 2512, 2485 (doesn't lock to these) PC board jack: 215 Specifications Wire Gauge: 20 AWG Barrel Length: 9.5 mm   Click Here for Catalog Picture Price:  $2.96
	2.5 mm ID x 5.5 mm OD Right Angle 6' Stripped End 24 AWG Cord Philmore TC250 Right angle plug is molded to a six foot cable. The other end is stripped and tinned. Mates to: Inline jack: # 258 Inline jack with cord: 48-258, 48-288 and CA206INL10FT18AWG-ST Chassis jack: # 248,249,325 Chassis locking jack: 2512, 2485 (doesn't lock to these) PC board jack: # 215 Specifications: Wire Gauge: 24 AWG Barrel Length: 11.50 mm   Click Here for Catalog Picture Price:  $1.96
2.5 mm ID x 5.5 mm OD Right Angle 6' Stripped End 20 AWG Cord Calrad 55-839B-RT Right angle plug is molded to a six foot cable. The other end is stripped and tinned. Mates with: Inline jack: 258 Inline jack with cord: 48-258, 48-288 and CA206INL10FT18AWG-ST Chassis jack: 248,249,325 Chassis locking jack: 2512, 2485 (doesn't lock to these) Mates with PC board jack: 215 Specifications: Wire Gauge: 20 AWG Barrel Length: 10.0 mm   Price:  $2.79
	2.5 mm ID x 5.5 mm OD Right Angle 6' Stripped End 18 AWG Cord Philmore 48-228 Right angle plug is molded to a six foot cable. The other end is stripped and tinned. Mates to: Inline jack: 258 Inline jack with cord: 48-258, 48-288 and CA206INL10FT18AWG-ST Chassis jack: 248,249,325 Chassis locking jack: 2512, 2485 (doesn't lock to these) PC board jack: 215 Specifications: Wire Gauge: 18 AWG Barrel Length: 12 mm   Click Here for Catalog Picture Price:  $2.56
3.3 mm ID x 5.5 mm OD and 1 mm Center Pin 6' Stripped End 24 AWG Cord Philmore 48-420 Plug is molded to a six foot cable. The other end is stripped and tinned. Mates to: Chassis jack: # 355 In-Line jack # 264 PC board jack: # 213 Specifications: Wire Gauge: 24 AWG Complies with EIAJ (Electronic Industries Association of Japan) class 4 or IV RC-5320 Standards. Mates with Sony video camera model DS70  Click Here for Catalog Picture Price:  $1.96
	4.1 mm ID x 7.0mm OD 1.0 mm Center Pin with 6' Stripped End 24 AWG Cord Philmore 48-412 Plug is molded to a six foot cable. The other end is stripped and tinned. Mates with Super Nintendo Wire Gauge: 24 AWG  Click Here for Catalog Picture Price:  $1.96
4.3 mm ID x 6.5mm OD 1.4 mm Center Pin Right Angle 6' Stripped End 18 AWG Cord Philmore TC265 Right angle plug is molded to a six foot cable. The other end is stripped and tinned. Mates to: Chassis jack 365 In-line jack 266 PC board jack 214 Specifications: Barrel Length: 0.365" (9.27mm) Wire Gauge: 18 AWG Complies with EIAJ (Electronic Industries Association of Japan) class 5 or V RC-5320 Standards. Made in Japan This cable is used on the Fujitsu ST5031d Tablet PC   Click Here for Catalog Picture Price:  $6.49

Online Catalog:Philmore and Calrad Electronics :Plugs, Jacks, Adapters and Cables:Coaxial Power Plugs/Jacks and Cables:Coaxial Power Plugs With Cord

Minute Man Electronics

$20.00 Minimum Merchandise Order - Thank You!