| | |
 | Desktop Stowaway Microphone Stand
Philmore 71-4503
It looks like a miniature space probe when collapsed for travel, but it's actually a tough little stand that can be set up in a few seconds. The leg assembly unscrewsfrom the upper cone assembly and the legs collapse and store inside. Made of a tough fiber filled plastic. Reduces to a 5 - 1/4" long cone. Standard 5/8 - 27 thread on top, accommodates standard microphone holders.
Price: $5.57
|
| |
|
Desktop Adjustable Microphone Stand
Philmore 71-4512
This is all-time standard desktop style, a 5 - 1/4" diameter, round, die cast iron base (black finished) with an adjustable chrome shaft. Hight may be adjusted from approximately 7.5 to 13.5 inches. Sure-locking Collett prevents slipping and will last indefinatly. Standard 5/8" - 27 threads at top accepts threaded microphone holders.
Price: $16.59
|  |
| |
|
 | 5' Chrome Adjustable Floor Mic Stand
Philmore 71-4652
This is a chrome microphone stand with a die-cast base and is adjustable in height. The upright may be adjusted from approximately 32" to 60 " in height. The addition of a microphone and a holder will usually take the mike will increase that height about 6" for a total maximum of 5-1/2 feet. Heavy rubber feet eliminate floor noise; and postive locking collets assure that the height will stay where you have placed it.
Price: $28.95
|
| |
|
5' All Black Adjustable Floor Mic Stand
Philmore 71-4653
This is an all balck microphone stand with a die-cast base and is adjustable in height. The upright may be adjusted from approximately 32" to 60 " in height. The addition of a microphone and a holder will usually take the mike will increase that height about 6" for a total maximum of 5-1/2 feet. Heavy rubber feet eliminate floor noise; and postive locking collets assure that the height will stay where you have placed it.
Price: $28.95
| |
| |
|
 | Desk Microphone Stand "U" Shaped
Calrad 10-55
A beautiful modernistic desk stand. "U" shaped base finished in black. Supplied with a polished chrome upright tube, threaded 5/8" - 27 at both ends. Can be used with the other microphone accessories. Size is 6-1/4" L x 4-3/8" (widest width) x 1-1/2" H (thickest height)
Price: $13.50
|
| |
|
Desktop Gooseneck Microphone Stand
Philmore 71-4507
An iron, die-cast base and flexible gooseneck mircophone stand. Rubber feet and a vinyl clad base provide for quite use. The 5/8" - 27 thread on top accomodates standard microphone holders. The entire stand is a low refelecting black finish. The gooseneck may be unthreaded from the base for transport for use with other stand parts. Total height is 13.5"
Price: $12.95
|  |
| |
|
 | Deluxe Desktop Microphone Stand
Philmore 71-4517
For very serious use, such as interviews, recording commercials or radio work, this is a fine stand with several very important features.
- The boom is removable for those occasions when you wish the stand and shaft alone.
- The height adjusts from about 9" to 15".
- Accomodate any standard 5/8" x 27 microphone holder
- The boom is 17" long and may be adjusted "in" or "out" as well as set at any angle necessary.
- Secure cam will hold a microphone exactly where you place it.
- The die-cast iorn base is nicely finished (soft black) and has rubber feet to prefvent marring the table surfaces.
- May be silently readjusted/repositioned for changing users.
This is a professional quality microphone stand and priced far below professional cost. and will acc
Price: $34.95
|
| |
|
Add-On Microphone Boom
Chrome - Philmore 71-4666
This is a handy chrome accessory for use with microphone floor stands. An adjustable boom tha can accomodate a second microphone for an instrument, other vocalists etc., or simply to hold a set of stereo microphones on one stand and boom. The 32" long boom may be adjusted "in" and "out" as well as angled up or down to any useful angle. The boom shaft has a standard 5/8" - 27 thread to accomodate standard microphone holders. Positive-lociking cam for quick, quiet adjustments. The boom is avialble in conventional chrome plating or in non-refelecting black finish to match microphone floor stands on this page.
Price: $17.95
|  |
| |
|
| | Add-On Microphone Boom
Black - Philmore 71-4666
This is a handy non-reflective black accessory for use with microphone floor stands. An adjustable boom tha can accomodate a second microphone for an instrument, other vocalists etc., or simply to hold a set of stereo microphones on one stand and boom. The 32" long boom may be adjusted "in" and "out" as well as angled up or down to any useful angle. The boom shaft has a standard 5/8" - 27 thread to accomodate standard microphone holders. Positive-lociking cam for quick, quiet adjustments. The boom is avialble in conventional chrome plating or in non-refelecting black finish to match microphone floor stands on this page.
Price: $17.95
|
| |
|
4 Multi-Color 1-3/4" Microphone Windscreen Set
Philmore # MW1
Contains four 1-3/4" high windscreens to fit over 1" to 1- 3/8" diameter microphones. Colors: Red -Yellow - Green - Black. Each soft foam screen adds depth and beauty that the entertainer will find hard to resist. Instant color is added to his/her act. Unwanted "breath" noise due to close talking is eliminated when windscreen is slipped over microphone. POP and WIND Noise usually associated with outdoor use is filtered out as the foam material is made of open pore urethane foam. Indoors or out, any microphone can now look different each time - and sound the same every time. A tip for users of mike mixers - avoid mike mix ups. Identify each mixer control with the color of the windscreen on the microphone it controls.
Price: $6.59
|  |
| |
|
| | 4 Multi-Color 2-2/4" Microphone Windscreen Set
Philmore # MW2
Contains four 2-3/4" high windscreens to fit over 1-3/8" to 1- 3/4" diameter microphones. Colors: Red -Yellow - Green - Black. Each soft foam screen adds depth and beauty that the entertainer will find hard to resist. Instant color is added to his/her act. Unwanted "breath" noise due to close talking is eliminated when windscreen is slipped over microphone. POP and WIND Noise usually associated with outdoor use is filtered out as the foam material is made of open pore urethane foam. Indoors or out, any microphone can now look different each time - and sound the same every time. A tip for users of mike mixers - avoid mike mix ups. Identify each mixer control with the color of the windscreen on the microphone it controls.
Price: $6.97
|
| |
|
2 Multi-Color 2-3/8" Microphone Windscreen Set
Philmore # MW3
Contains two 2-3/8" high windscreens to fit over 1-3/4" to 2" diameter microphones. Colors: Red - Green. Each soft foam screen adds depth and beauty that the entertainer will find hard to resist. Instant color is added to his/her act. Unwanted "breath" noise due to close talking is eliminated when windscreen is slipped over microphone. POP and WIND Noise usually associated with outdoor use is filtered out as the foam material is made of open pore urethane foam. Indoors or out, any microphone can now look different each time - and sound the same every time. A tip for users of mike mixers - avoid mike mix ups. Identify each mixer control with the color of the windscreen on the microphone it controls.
Price: $3.89
|  |
| |
|
 | Dark Gray 2-3/8" Microphone Windscreen Set
Philmore # MW4
Contains one dark gray 2-3/8" high windscreens to fit over 1-3/4" to 2" diameter microphones. Each soft foam screen adds depth and beauty that the entertainer will find hard to resist. Instant color is added to his/her act. Unwanted "breath" noise due to close talking is eliminated when windscreen is slipped over microphone. POP and WIND Noise usually associated with outdoor use is filtered out as the foam material is made of open pore urethane foam. Indoors or out, any microphone can now look different each time - and sound the same every time. A tip for users of mike mixers - avoid mike mix ups. Identify each mixer control with the color of the windscreen on the microphone it controls.
Price: $2.69
|
| |
|
Microphone Stand Desktop Tripod
Calrad 10-56
Same as Speco MST-1This microphone stand desktop tripod is 5 inches high. A microphone adapter is included
Price: $7.49
|  |
| |
|
 | Desktop Microphone Base
Calrad 10-19
This is a desktop microphone base with a push on/push off talk switch with red LED indicator. Plug gooseneck microphones into the female XLR mic input and connect your cable to the male XLR output. Sturdy 2 lb weighted black base. Requires 2 AAA batteries for the LED indicator.
Price: $38.95
|
| |
|
Female XLR Desktop Black Mount
Calrad 30-590-BK
This is a black female XLR desktop mount used for quick release style gooseneck mics. It has a removable female for easy soldering. Mounts with 3 included screws. Base diameter is 1.75" x 2" height.
Price: $5.95
|  |
| |
|
 | Male 1-3/4" Flange Gooseneck Base
Philmore 71-4001
Same as Speco Technology MAD-12M, Calrad 10-34Designed for surface mounting on a table top, side wall etc., will accommodae a gooseneck or microphone extension pipe. Fits most gooseneck types with 5/8" - 27 threads. Chrome plaed base has MALE threads. 1- 3/4" base diameter.
Price: $3.89
|
| |
|
Female 1-3/4" Flange Gooseneck Base
Calrad 10-35
Same as Speco Technology MAD-11FDesigned for surface mounting on a table top, side wall etc., will accommodate a gooseneck or microphone extension pipe. Fits most gooseneck types with 5/8" - 27 threads. Chrome plaed base has FEMALE threads. 1- 3/4" base diameter.
Price: $5.29
|  |
| |
|
 | Male 2-3/4" Flange Gooseneck Base
Philmore 71-4005
Designed for mounting on a table top, side wall etc., will accommodate a gooseneck or microphone extension pipe. Made for use as a permanent mount. This larger diameter is suggested for better strength if use will be constant and rigorous. Fits most gooseneck types with 5/8" - 27 threads. Chrome plaed base has MALE threads. 2 - 3/4" base diameter.
Price: $4.29
|
| |
|
Female 2-3/4" Flange Gooseneck Base
Philmore 71-4007
Designed for mounting on a table top, side wall etc., will accommodate a gooseneck or microphone extension pipe. Made for use as a permanent mount. This larger diameter is suggested for better strength if use will be constant and rigorous. Fits most gooseneck types with 5/8" - 27 threads. Chrome plaed base has FEMALE threads. 2 - 3/4" base diameter.
Price: $4.29
|  |
| |
|
 | 3" Mike Pipe
Philmore 71-4010
Use with flange mounts with bases for table microphone stands etc. The 3" pipe is chrome plated, threaded on each end with standard 5/8" - 27 threads to mate with standard microphone holders and bases. Included is a star nut that can be used to tighten the pipe against the mike holder, which prevents loosening.
Price: $3.59
|
| |
|
Microphone Holder Adapter
3/8"-17 Female to 5/8"- 27 Male
Philmore 71-4015
Microphone holders and stands are supplied with one of two different size threads. The 5/8" - 27 size is one and the 3/8" - 17 is the other. If you have a mike holder of one size and a stand with the other, you'll need an adaptor to use them together. See our 71-4016 also. One of these will solve the problem; road groups should carry a few of each size.
Price: $2.26
|  |
| |
|
 | Microphone Holder Adapter
3/8"-17 Male to 5/8"- 27 Female
Philmore 71-4016
Microphone holders and stands are supplied with one of two different size threads. The 5/8" - 27 size is one and the 3/8" - 17 is the other. If you have a mike holder of one size and a stand with the other, you'll need an adaptor to use them together. See our 71-4015 also. One of these will solve the problem; road groups should carry a few of each size.
Price: $2.86
|
| |
|
6" Chrome Goose Neck
Philmore 71-4031
Same as Calrad 10-35-6 and Speco Model MGN-13 This microphone gooseneck has a standard 5/8" X 27 connecting thread. Male on one end and female on the other.
Price: $4.95
|  |
| |
|
 | 6" Black Goose Neck
Philmore 71-4030
Same as Calrad 10-36-6BK and Speco Model MGN-13 This microphone gooseneck has a standard 5/8" X 27 connecting thread. Male on one end and female on the other.
Price: $4.95
|
| |
|
13" Chrome Goose Neck
Philmore 71-4041
Same as Speco Model MGN-13 and Calrad 10-36-13This microphone gooseneck has a standard 5/8" X 27 connecting thread. Male on one end and female on the other.
Price: $5.95
| |
| |
|
 | 13" Black Goose Neck
Philmore 71-4040
Same as Speco MGN-13B and Calrad 10-36-13BKThis black microphone gooseneck has a standard 5/8" X 27 connecting thread. Male on one end and female on the other.
Price: $5.95
|
| |
|
19" Chrome Goose Neck
Calrad 10-36-19
Same as Speco Model MGN-19This microphone gooseneck has a standard 5/8" X 27 connecting thread . Male thread on one end and female on the other.
Price: $9.49
| |
| |
|
| | 19" Black Goose Neck
Calrad 10-36-19BK
This microphone gooseneck has a standard 5/8" X 27 connecting thread. Male on one end and female on the other.
Price: $8.95
|
| |
|
Microphone Stand Holder
Philmore SM70
Same as Speco MSA-2Holds microphone firmly with no compromise. Slide in any microphone having a 3/4" to 1-1/4" diamer handle. This black holder is sharp looking with all microphones. Firm swivel adaptor tilts through 180 degrees. Has standard 5/8" - 27 threads.
Price: $4.65
|  |
| |
|
 | Microphone Stand Holder
Philmore SM85
Same as Speco MSA-1This adjustable microphone holder adapts to the body of microphones from small cassette to larger professionals types. A squeeze of the handle, and the holder grips the microphone with a secure grooved ridge contact. This holder accomodates microphone handle diameters from 5/8 to 1-3/8 inches. It tilts a full 180 degrees and the female end accepts standard male microphone stand or gooseneck 5/8" - 27 thread fittings.
Price: $5.55
|
| |
|
Stereo Pre-Amplfier
Convert from Crystal to Magnetic
Cartridge - Philmore PRE600
This high quality stereo pre-amplifier will allow you to replace a crystal or ceramic phono cardridge with a better quality magnetic stereo cartridge while using the original stereo amplifier supplied with your turntable. The use of this pre-amplifer in conjunction with a magnetic cartridge will give you CD quality sound out of your vintage turntable. Improved circuitry and filtering in the power supply results in lower hum while maintaining an isolated ground loop. Specifications:
- Frequency Response: 30-20,000 Hz Equalized RIAA
- Input Impedance: 50K Ohm
- Maximum Output: 1.8 V (less than 1% distortion)
- Output Load: 50K Ohms
- S/N Ratio: Over 60db
- Power Supply: 117VAC, 50-60 Hz .1 watt
Price: $22.95
|  |
| |
