| | |
 | Neg-Fast® Generation II Film
Pack of six 5' X 6"- Datak 12-720
Use this Neg-fast® Generation II Film along with the following materials to create high-quality PC boards from a photocopy of a magazine or positive artwork from a CAD program. You will also need the following materials:
- Neg-Fast® Generation II Film Developer and Fixer #
12-710; needed with this film to create the negative.
- Copper Clad Boards; available in single or double sided. PCB35
- Negative Acting Liquid Photo Resist # ER-71; sprayed on to make the board sensitve to UV light.
- UV Exposure Bulb # ER-2000; for exposing the sensitized board - about 4 minutes.
- Contact Exposure Frame # ER10
or ER56; to hold the film and board together during the exposure.
- Etching Trays;
to contain the developer; available in several sizes.
- Negative Resist Developer # ER-8; dissolves resist areas that are not harded by the UV light.
- High Speed Steel Drill Bits
High Speed Steel Drill Bits for drilling PCB holes; available in common sizes.
This film is UV sensitive and should be handled under subdued light; we recommend a yellow 'bug' light of about 25 watts. Complete instructions are enclosed.
Price: $7.94
|
| |
|
Neg-Fast® Generation II Film
Pack of two 8" x 11"- Datak 12-730
Use this Neg-fast® Generation II Film along with the following materials to create high-quality PC boards from a photocopy of a magazine or positive artwork from a CAD program. You will also need the following materials:
- Neg-Fast® Generation II Film Developer and Fixer #
12-710; needed with this film to create the negative.
- Copper Clad Boards; available in single or double sided. PCB35
- Negative Acting Liquid Photo Resist # ER-71; sprayed on to make the board sensitve to UV light.
- UV Exposure Bulb # ER-2000; for exposing the sensitized board - about 4 minutes.
- Contact Exposure Frame # ER10
or ER56; to hold the film and board together during the exposure.
- Etching Trays;
to contain the developer; available in several sizes.
- Negative Resist Developer # ER-8; dissolves resist areas that are not harded by the UV light.
- High Speed Steel Drill Bits
High Speed Steel Drill Bits for drilling PCB holes; available in common sizes.
This film is UV sensitive and should be handled under subdued light; we recommend a yellow 'bug' light of about 25 watts. Complete instructions are enclosed.
Price: $7.94
| |
| |
|
 | Copy Clear Sheets
For Making Positive Films
Pack of 5
Philmore Datak 12-500
For use in laser printers and most dry toner copy machines to make film positives for, but not limited to, the Datak presensitized PC boards. Scan in magazine circuit layouts or design your own, then print the results on these sheets.
Price: $4.26
|
| |
|
Developer and Fixer for Neg-Fast® Generation II Film
4 Oz Each - Datak 12-710
Note: This chemical product can not ship by air.
Price: $7.94
|  |
| |
|
 | Datak System Instruction Manual
Datak #12-760A
A manual that gives detailed instructions for most of the Datak PC board making products including:
- Neg-Fast® film
- Negative Photo Resist
- Presensitized PC Board
- Tinnit™ Tin Plating
- Etching
A complete guide for PC board making via DATAK products
Price: $1.99
|
| |
|
Ferric Chloride Liquid Etching Solution 1 Quart (32 Oz)
Philmore P/N 12-2038
Same as GC 22-238 or M.G. Chemicals 415-500ml
Note: This chemical product can not ship by air.
This is 1 quart of Liquid Ferric Chloride (FeCL) by Datak that etches approximately 960 square inches of standard copper board. This Ferric Chloride solution is one of the most effective and safest etching materials for copper clad PC boards, however special care should be taken when using etching chemicals.
- Use only in plastic or glass trays. See etching trays below.
- Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.
- Ferric chloride is highly corrosive to metal and injestion can be fatal.
Price: $11.92
|  |
| |
|
| | Ferric Chloride Liquid Etching Solution 1 Gallon (128 Oz)
Philmore P/N 12-2039
Note: This chemical product can not ship by air.
This is 1 gallon of Liquid Ferric Chloride (FeCL) by Datak that etches approximately 3,840 square inches of standard copper board. This Ferric Chloride solution is one of the most effective and safest etching materials for copper clad PC boards, however special care should be taken when using etching chemicals.
- Use only in plastic or glass trays. See etching trays below.
- Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.
- Ferric chloride is highly corrosive to metal and injestion can be fatal.
Price: $35.11
|
| |
|
Ferric Chloride Dry Concentrate
Etchant 1/4 lb
Philmore Datak ER3
Note: This chemical product can not ship by air.
This is Datak's Dry Powder Ferric Chloride (FeCL) that is mixed with water to make the etching solution. This 1/4 lb package produces 1 pint, which etches approximately 200 square inches of standard copper board. Ferric Chloride solution is one of the most effective and safest etching materials for copper clad PC boards, however special care should be taken when using etching chemicals.
- Use only in plastic or glass trays. See etching trays below.
- Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.
- Ferric chloride is highly corrosive to metal and injestion can be fatal.
Price: $5.66
|  |
| |
|
| | Ferric Chloride Dry Concentrate
Etchant 1 lb
Philmore Datak ER21
Note: This chemical product can not ship by air. This is Datak's Dry Powder Ferric Chloride (FeCL) that is mixed with water to make the etching solution. This 1 lb package produces 1/2 gallon, which etches approximately 800 square inches of standard copper board. Ferric Chloride solution is one of the most effective and safest etching materials for copper clad PC boards, however special care should be taken when using etching chemicals.
- Use only in plastic or glass trays. See etching trays below.
- Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.
- Ferric chloride is highly corrosive to metal and injestion can be fatal.
Price: $16.39
|
| |
|
Ferric Chloride Dry Concentrate
Etchant 2 lb
Philmore Datak ER22
Temporarily Out of StockNote: This chemical product can not ship by air. This is Datak's Dry Powder Ferric Chloride (FeCL) that is mixed with water to make the etching solution. This 2 lb package produces 1 gallon, which etches approximately 1600 square inches of standard copper board. Ferric Chloride solution is one of the most effective and safest etching materials for copper clad PC boards, however special care should be taken when using etching chemicals.
- Use only in plastic or glass trays. See etching trays below.
- Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.
- Ferric chloride is highly corrosive to metal and injestion can be fatal.
Price: $21.16
| |
| |
|
 | Nitrile Disposable Glove (1 Pair)
Philmore P/N 12-510
These gloves are perfect for use when working with chemicals involved iwth making P.C. boards. Good for use with photo chemicals (negative or positive) and feric choride etching solution.
Price: $1.19
|
| |
|
Etch Resist Ink Pen 1/64" Wide
Datak # ER25
Same as GC 22-222For making resist circuits directly on PC boards. These pens are filled with lacquer ink that is resistant against aqueous PC etch solutions. Dries instantly. Can be removed with FINE steel wool or alcohol. Draws thin width lines of approximately 1/64"
Price: $2.57
|  |
| |
|
| | Etch Resist Ink Pen 1/32" Wide
Datak # ER15
Same as GC 22-220For making resist circuits directly on PC boards. These pens are filled with lacquer ink that is resistant against aqueous PC etch solutions. Dries instantly. Can be removed with FINE steel wool or alcohol. Draws thin width lines of approximately 1/32"
Price: $2.25
|
| |
|
Etch Resist Lacquer 1/2 Fl Oz
GC Waldom 22-244
Note: This chemical product can not ship by air. For creating, modifying or touching-up resist patterns before etching. Fast drying, and easy to apply on PC boards. Bottle is supplied with small brush attached to cap. Brush attached inside cap or works well with fine artists brushes.
Price: $8.95
|  |
| OUT OF STOCK |
|
 | Photo Resist - Negative Acting
Philmore Datak ER-71
Note: This chemical product can not ship by air. A liquid spray-on coating in its own spray bottle. The process of pcb making or metal etching starts with first coating the board (or metal) with this resist. Next the material is exposed with UV light, (See # ER2000 below)
through your artwork or pcb layout. It is then developed in the ER-8 liquid developer, which causes the exposed resist to harden, while the unexposed resist washes off. The hardened areas are then protected from the ferric chloride etchant bath while the remaining areas are removed or etched. The end result is a high quality pcb or metal etching. This material is negative acting meaning it requires a negative image. - Coats approx. 1700 Sq. inches.
- May be flow coated or brushed.
- Ideal exposure is at 365 millimicrons +10/-15 millimicrons.
Use chemical gloves when handling this product.See our Nitrile Glove P/N 12-510.Here is a product trick using an old turntable / record player: For a more uniform coating use a throw away turntable that is set at 45 RPM. With the spindle removed and the PC board mounted on the platter, apply the material on the center of the board. Turn the player on and let the centrifical force flow coat the PCB surface. The turntable dust cover also works great for keeping dust and light off the board while drying. Cover the dust cover with anything that will keep the light out.
Click Here for Instructions
Price: $10.47
|
| |
|
Exposure Bulb for Negative Acting Resist
Philmore Datak ER2000
UV source for DATAK
- Neg-FastŠ film
- Negative Acting Photo-Resist
Price: $14.95
|  |
| |
|
 | Resist Developer - Negative
Philmore Datak ER-8
Note: This chemical product can not ship by air. This developer will develop the ER-71 Negative Acting Resist; resist areas not hardened via UV light are dissolved away. UV hardened areas remain to resist the etchant. Use this product in aluminum trays only, as it will dissolve nearly any plastic tray. Use our 12-520. Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.
Price: $6.49
|
| |
|
Developer - Positive Type 2 oz Concentrated
Philmore Datak # 12-402
Note: This chemical product can not ship by air.
For developing Philmore's presensitized PC boards. Developer is mixed 10 parts tap water to 1 part concentrate. Ten fully dilluted ounces will develope between 12 and 22 square feet of precoated board (depending upon circuit density). This mild sodium hydroxide solution with additives may be flushed down the drain after use. Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.
Price: $8.86
|  |
| |
|
| | Developer - Positive Type 4 oz Concentrated
Philmore Datak # 12-404
Note: This chemical product can not ship by air.
For developing Philmore's presensitized PC boards. Developer is mixed 10 parts tap water to 1 part concentrate. Ten fully dilluted ounces will develope between 12 and 22 square feet of precoated board (depending upon circuit density). This mild sodium hydroxide solution with additives may be flushed down the drain after use. Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.
Price: $15.52
|
| |
|
Tinnit™ Tin Plate
Makes 1 Pint
Philmore Datak # ER18
Note: This chemical product can not ship by air. Use Tinnit™ to plate bare copper circuit boards to enhance solderability, resist oxidation and improve the appearance. It has also been used to plate edge card connector fingers on prototypes when a low, stable contact resistance is needed, but gold is not available or desired. The powder makes one pint size of Tinnit™, which will plate up to 600 square inches of copper with approximately 0.0004" of bright tin. Plating is complete after about 10 minutes in a fresh solution. Adhesion and solderability are excellent. No electricity is required; the material tends to plate any metal that is chemically more active than tin and is not ozidized by the plating bath. Tinnit™ has been successfully used to plate brass, bronze, iron and some carbon steels. Tinnit© is supplied as a dry mixture with an indefinite shelf life, however when mixed with water, the solution has a life of approximately two months. You need add no acid or other materials to this solution. Tinnit™ contains all plating chemicals plus surfactants and cleaners to insure a perfect plate. Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.
Price: $7.89
|  |
| |
|
| | Tinnit™ Tin Plate
Makes 1/2 Gallon
Philmore Datak # ER181
Note: This chemical product can not ship by air. Use Tinnit™ to plate bare copper circuit boards to enhance solderability, resist oxidation and improve the appearance. It has also been used to plate edge card connector fingers on prototypes when a low, stable contact resistance is needed, but gold is not available or desired. This powder makes 1/2 gallon size of Tinnit™, which will plate up to 2400 square inches of copper with approximately 0.0004" of bright tin. Plating is complete after about 10 minutes in a fresh solution. Adhesion and solderability are excellent. No electricity is required; the material tends to plate any metal that is chemically more active than tin and is not ozidized by the plating bath. Tinnit™ has been successfully used to plate brass, bronze, iron and some carbon steels. Tinnit© is supplied as a dry mixture with an indefinite shelf life, however when mixed with water, the solution has a life of approximately two months. You need add no acid or other materials to this solution. Tinnit™ contains all plating chemicals plus surfactants and cleaners to insure a perfect plate. Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.
Price: $22.56
|
| |
|
Tinnit™ Kit
Philmore Datak 12-800
Note: This chemical product can not ship by air. Tin plating enhances solderabilty, resists oxidation and provides a professionally appearance. This kit includes:
- Package of dry concentrate Tinnit ™, which is enough to make 1 pint of liquid.
- 16 oz. bottle for storing Tinnit between uses.
- Plastic Tray for application
- Handling tool
Use chemical gloves when handling this product. See our Nitrile Glove P/N 12-510.The Tinnit™ in this kit will plate a copper clad board with a bright, protective tin plate approximately .0004" thick over an area of 600 sq. inches.
Price: $17.54
|  |
| |
|
 | Power Etch Pump
Philmore Datak ER12
Automatically etches PC boards fast!This pump comes with a coupling hose, perforated distributor tube and complete instructions. Accelerates etching and frees you from constant agitating of the etch solution. Bubbles provide both agitation and also some oxygen which enhances the process.
Price: $10.16
|
| |
|
Etching Solution Heater
Waldom 22-392
Similar to the Philmore 12-702This is a heater for keeping pcb etchant solution at the optimum temperature. It heats the solution up to 38° C (100° F). It is used to further reduce the etching time. It has a built-in adjustable thermostat.
- Adjustable Temperature
- Thermostat Control
- Adjustable Mounting Clamp
- Length: 8-3/4"
- Emersion Depth is 7-7/8"
- 120VAC 100 Watts
Price: $16.95
|  |
| |
|
 | PC Developing & Etching Tray
Plastic 5" X 7"
Philmore Datak 12-570
A lightweight, tough, stain resistant developing tray designed for use with printed circuit board developing solutions such as Datak # 12-402 and 12-404, and etching solutions such as ferric chloride.
Price: $7.99
|
| |
|
PC Developing & Etching Tray
Plastic 8" X 6" Pack of 2
Philmore Datak 12-515
Note: This item does not have the pourable corner as shown in the picture. A lightweight, stain resistant developing tray designed for use with printed circuit board developing solutions such as Datak # 12-402 and 12-404, and etching solutions such as ferric chloride.
Price: $9.66
| |
| |
|
| | PC Developing & Etching Tray
Plastic 8" X 10"
Philmore Datak 12-810
A lightweight, tough, stain resistant developing tray designed for use with printed circuit board developing solutions such as Datak # 12-402 and 12-404, and etching solutions such as ferric chloride.
Price: $8.49
|
| |
|
PC Developing & Etching Tray
Plastic 11" X 14"
Philmore Datak 12-1114
A lightweight, tough, stain resistant developing tray designed for use with printed circuit board developing solutions such as Datak # 12-402 and 12-404, and etching solutions such as ferric chloride.
Price: $12.32
| |
| |
|
 | Aluminum Tray for Resist Developer
8" X 8" Pack of 2
Philmore Datak 12-520
This is an 8" x 8" x 1-3/4" deep aluminum tray (pack of 2) to be used with the ER-8 Resist Developer.
Price: $2.76
|
| |
|
Contact Exposure Frame 5" X 6"
Philmore Datak ER56
A contact frame is needed to hold the film and PC boards during the exposure. This Spring Loaded, Steel Frame comes complete with glass, back board, and instructions.
Price: $18.96
|  |
| |
|
| | Contact Exposure Frame 9" X 12"
Philmore Datak ER10
This Metal frame with slide-in glass and wood trays; holds the positive "art" tightly against board during exposure to the light source. Two sizes are available. This Spring Loaded, Steel Frame comes complete with glass, back board, and instructions.
Price: $27.39
|
| |
|
Drafting Patterns
GC Waldom # 21-677
An 8-1/2" x 11" sheet containing two dozen of the most commonly used pre-spaced component configurations. Self-adhesive pads may easily be removed from master sheet with printed circuit knife and placed upon Mylar positive artwork. A highly refined process and ink assures true opacity and the excellent definition necessary for quality printed circuit work.
- High Opacity
- Perfect Registration
- Maybe Relifited and Repositioned
Price: $7.39
|  |
| |
|
 | Drill Bit Set
Philmore / Datak 12-530
For drilling component lead wire holes in phenolic and glass epoxy PC boards. Made of high speed tool steel for long life. Set contains one each of:
- Bit No. 70 - 0.028" Dia
- Bit No. 67 - 0.032" Dia
- Bit No. 65 - 0.035" Dia
.
Price: $8.59
|
| |
|
Drill Bit Set
Philmore / Datak 12-550
For drilling component lead wire holes in phenolic and glass epoxy PC boards. Made of high speed tool steel for long life. Set contains one each of:
- Bit No. 60 - 0.040" Dia
- Bit No. 55 - 0.052" Dia
- Bit No. 52 - 0.064" Dia
.
Price: $6.47
| |
| |
|
 | PC Board Trace Maker
Circuit-Fix ™
Philmore CF-1
The CIRCUIT-FIX system has been designed to allow you to cut accurate, burr-free copper foil traces for PC boards for the purpose of adding to, or repairing a circuit board. CIRCUIT-FIX is a handy system whether for prototype modifications or for circuit repairs. The system centers on a spring-loaded clamp and cutting guide that permits excellent trace cutting with a modeling knife. Both the knife and a sheet of self adhesive copper trace (our CF-3) material are included. Also included is a sheet of (assorted sizes) pure copper self-adhesive donut pads (our CR2). The cut trace and donuts are burnished to the board and then soldered to component leads. The copper donuts foil are 1 Oz. copper 0.0016" thickness and is passivated to retard corrosion and permits easy soldering.
Price: $22.41
|
| |
|
Copper Foil 3.25" x 10"
2 Sheets Philmore CF3
For use in printed circuit modifications. This is two sheets of 3-1/4 x 10" adhesive backed 1 oz copper foil that is 0.0016" thick. The copper is passivated to retard corrosion and permit easy soldering. Although this item can be used for other applications, this item is also the refill for model CF-1 Circuit-Fix™ PC Board Trace Maker
Price: $6.56
|  |
| |
|
 | Copper Donuts, Assorted Sizes
Philmore Datak CF-2
Consists of 308 adhesive copper donuts for pcb repair. The pad is burnished (see our burnishing tool 04158) to the board and soldered to the component lead. The assortment comes in the following sizes:
- 48 donuts - 1/16"
- 72 donuts - 3/32"
- 150 donuts - 1/8"
- 48 donuts - 5/32"
This copper donuts are 1 oz copper, .0016" thickness. The copper is passivated to retard corrosion and permit easy soldering. This pack is included with the CF-1 Circuit-Fix System.
Price: $5.49
|
| |
|
Pure Copper 1/8" Circuit Tape
GC / Waldom 22-511
This is a 20 foot roll of self-adhesive pure 0.0014" x 20' long copper circuit tape for quick repairs or circuit modification. Adheres readily to PC boards and similar surfaces; solders readily. Flexible enough to be used around corners, between PC boards, between board and chassis, etc. Extremely low resistance.
Price: $11.95
|  |
| |
